------------------------------------------------------------------------
---      Xerox Document Centre 400/350/250 PCL 6 Version 2.0.4TC     ---
---              Printer Driver for Windows NT(R)4.0/2000            ---
---                          March 2002                              ---
---                                                                  ---
---                             Readme                               ---
------------------------------------------------------------------------


This document describes

  1.  Installation file list.
  2.1 Installation of this driver.
  2.2 Installation under Windows NT(R)4.0/2000 (Setup.exe)
  2.3 Uninstallation. (Setup.exe)
  3.1 Installation under WindowsNT(R)4.0 (Add Printer Wizard)
  3.2 Uninstallation. (Add Printer Wizard)
  4.1 Installation under Windows(R)2000 (Add Printer Wizard)
  4.2 Uninstallation. (Add Printer Wizard)
  5.  Notes for Watermarks.
  6.  General Comments.
  7.  Limitations.
  8.  Known Problems.



1. Installation file list
=========================

DC406TK.DLL
DC406TL.DLL
DC406TX.DLL
DC406TC.DLL
DC406TU.DLL
DC406TP.DLL
DC406TS.DLL
DC406TZU.DLL
DC406TZK.DLL
DC406TWU.DLL
DC406TWK.DLL
DC406TJ.DLL
DC406TQ.EXE
DC406T.HLP
DC406TI3.DLL
DC406TZ.EXE
DC406TZ1.EXE
                                  
SETUP.EXE
UNSETUP.EXE
OEMSETUP.INF

FXXLLSTH.INF
FXXLLSTI.INF


2.1 Installation of this driver
===============================

**Note**
Driver installation by Windows Add Printer Wizard is permitted only for
users who obtain driver distribution files via the CD-ROM or floppy disk
from Fuji Xerox Co., Ltd..
If your driver distribution files are received via electronic mail or by
downloading from WWW, you should run the driver Setup.exe to install it.
During the SetUp operation, you have to agree and accept the End User
License Agreement in order to proceed for a successful driver installation.



2.2 Installation under Windows NT(R)4.0/2000 (Setup.exe)
========================================================

(1) Start Windows NT(R)4.0/2000 and insert the "PCL Driver/Network Utility"
    CD-ROM in the CD-ROM drive.

(2) Open the folder which contains the installer program.
    You can find the SETUP.EXE in this folder. Double click it to start
    the installer program. Note that the [Add Printer] icon in the
    [Printers] window in the [Control Panel] is not available for this
    printer driver.

(3) Read the End User License Agreement and turn on the check box left of
    [I accept the terms of the above License Agreement] if you accept the
    terms. Then click the [Next] button.
 
(4) Now, only selectable the printer model on the first dialog of 
    the installer is "Xerox DC 400/350/250 PCL 6 (T)". 

(5) Select the port used for the printer.

(6) If you DON'T want to make this the default printer, check it off and 
    click the [Next] button.

(7) If you want another name for this printer, input the name 
    and click the [Next] button.
    Default printer name is "Xerox DC 400/350/250 PCL 6 (T)"

(8) Click the [Finish] button on the [Ready to Start Copying] dialog box.

(9) When the copying of files is completed, the [INSTALLATION SUCCESSFUL]
    dialog box appears. Click the [Printer Properties] or [Document
   Defaults] to configure the printer driver, or [Exit to Windows] to finish
   installation.

(10) Restart Windows NT(R)4.0/2000 system to make use of the printer driver.



2.3 Uninstallation (Setup.exe)
==============================

(1) Execute "Unsetup.exe" in the same folder where you executed "Setup.exe"
    in the "PCL Driver/Network Utility" CD-ROM.

(2) Select printer model for "Xerox DC 400/350/250 PCL 6 (T)" in the 
    "Printer Uninstall" dialogue.If you changed the printer name, it is shown 
    in the printer model list. And click the [Next] button.

(3) Click the [Finish] button on the "Ready to Start Deleting" dialog.

(4) To ensure a completely clean system or to re-install the printer driver,
    You must restart Windows.



3.1 Installation under WindowsNT(R)4.0 (Add Printer Wizard)
===========================================================

(1) Start Windows NT(R)4.0 and insert the "PCL Driver/Network Utility" CD-ROM 
    in the CD-ROM drive.

(2) Click the [Add Printer] icon in the [Printers] windows from the [Control Panel]

(3) Following the steps of [Add Printer Wizard], you can choose the printer port.
 
(4) After you select the port of the printer, you will see the selection of
    [Manufactures:] and [Printers:]. Click [Have Disk...] in the dialog.

(5) Enter a path to a location of the INF file you are installing. (FXXLLSTH.INF)
    You can also indicate the INF file location by [Browse]. 
    Open the Drive into which you inserted the CD-ROM.
    Then select the INF file in the folder and then click [OK].

(6) "Xerox DC 400/350/250 PCL 6 (T)" appears in the [Printers:] in the dialog.
    Select the printer and click [Next].
 
(7) When you finished all the steps of the [Add Printer Wizard], printer icon 
    will be created in the [Printers] dialog.
    It is recommended that you print a test page after completion of the printer 
    driver installation in order to check if the driver was installed properly.



3.2 Uninstallation (Add Printer Wizard)
=======================================

(1) Delete the printer icon you installed in the [Printers] dialog from the 
    [Control Panel].



4.1 Installation under Windows(R)2000 (Add Printer Wizard)
==========================================================

Follow the instructions below to enable printing under Windows(R)2000.

(1) Click [Start], select [Settings], and then click [Printers].

(2) Double-click the [Add Printer] icon in the "Printers" dialog, 
    and then follow the instructions on the dialogs.

(3) If the printer is directly attached to your computer or is connected to
    the Network using the LPR protocol, choose [Local Printer] ,then click 
    [Next>] and follow the instructions from (7). Otherwise, choose 
    [Network printer].

  <Note> Please check off the [Automatically detect and install my Plug and
         Play printer].

(4) Connect to the desired printer by:
         * Searching for it in the Active Directory, or 
         * Clicking [Next>] to locate the printer on the network, or 
           typing its name using the following format. 
           
           \\printserver_name\share_name

    Then follow the instructions from (7).
    If you are not familiar with the network, please consult the network 
    administrator.

  <Note> Our products don't support the URL format connection.

(5) Select the printer port where the printer device is connected directly, click
    [Next>], and go to step (7).
    If the printer is connected to the Network using the LPR protocol,
    select [Standard TCP/IP Port] of the [Create a new port:] section,
    and then click [Next>]. The "Welcome to the Add Standard TCP/IP Printer
    Port Wizard" dialog will be displayed. Click [Next>].

(6) Enter the Printer Name or IP address in the [Printer Name or IP Address]
    edit box. If you don't know the Printer Name or IP address, please consult
    the network administrator.
    The "Completing the Add Standard TCP/IP Printer Port Wizard" dialog will
    be displayed. Click [Finish].

(7) Click [Have Disk....] in the "Add Printer Wizard" and select the 
    <FXXLLSTI.INF> file.

(8) If <FXXLLSTI.INF> is loaded correctly, the printer models are listed in the
    dialog box. Select the printer you use.

(9) You may change the printer name, set it as a default printer or a shared printer
    or print the test page as you like.

(10) Follow the instructions on the dialog to finish the driver installation.



4.2 Uninstallation (Add Printer Wizard)
=======================================


(1) Delete the printer icon you installed in the [Printers] dialog from the 
    [Control Panel].



5. Notes for Watermarks
=======================
The driver provides a wide input range in defining a watermark size,
length & position. Such flexible user input enables a watermark to be
created as small as to print on a Postcard or as large as to print on
an A3 paper. However, an extremely large watermark may not be printed
successfully on a relatively small paper in size.
It is the user's responsibility to define an appropriate watermark for
printing it on the selected paper type.

The Watermark Preview is close to the printed result but it may not
exactly match.
A watermark may not be printed correctly for these cases:

(1) Depending on the selected (bolded) font type, a watermark with long
    text length and/or huge text size may hit the maximum working memory
    limit. As a result, the actual output may differ from the desired
    output.

(2) Due to the technical limitation of Raster printing mode, a watermark 
    cannot be printed in background of a document.

(3) A watermark may be clipped by the printable area if it is printed
    across the printable margins. The Watermark Preview Window does not
    reflect the printable area of the selected paper size.


6. General Comments
===================

(1) It is recommended that you restart the Windows system after completion
    of driver installation in order for the driver to work properly.

(2) It is also strongly recommended that you restart the Windows system 
    after completion of driver uninstallation.
    This is to ensure a completely clean system especially if you are
    to perform re-installation of driver. 

(3) If you encounter problem in setting up the driver by SETUP.EXE, you may
    use the Windows Add Printer Wizard to install the driver.
    Please refer to Oemsetup.txt for guidelines of driver installation
    via the Windows Add Printer Wizard.

(4) After installing the Windows NT(R)4.0/2000 Xerox DC 400/350/250 PCL 6 
    printer driver, you may also install an alternate Windows 95/98 printer
    driver on the Windows NT(R)4.0/2000 system by running the SETUP.EXE provided 
    by the Windows 95/98 Xerox DC 400/350/250 PCL 6 printer driver. This will
    allow users on the Windows 95/98 system to download it automatically
    when they connect.

(5) Some applications provide printing options pertaining to the number
    of copies and collating copies.  Always select the printing options
    in the application unless the instructions specify otherwise.
    Use the printer driver dialogs to select advanced options such as
    duplex (2-sided) printing, or options that are not available in the
    application.

(6) If your Job Offset output does not work well with the collated copies,
    you may try to deselect the "Collate" option in the application
    and check the "Collate" check box in the printer driver.

(7) Always close the printer driver dialogs and/or the application Print
    dialog before you make any changes to the default settings of the
    printer driver via the Control Panel.

(8) Not all graphics and images can be printed using the "Vector" graphics
    setting. If you use the "Vector" setting and your graphic images do
    not print the same way they appear on your screen, select the "Raster"
    graphics setting and reprint your graphic.
    
(9) If you expect the printed texts to be "what you see is what you get",
    deselect the "Use Printer's TrueType Fonts" option.

(10) Select and deselect the "Use Printer's TrueType Fonts" option in driver
     will affect the layout of your print job.
     Use of Printer's TrueType Fonts will result in smaller size in texts,
     tables and graphic images printed.
     Do not select "Use Printer's TrueType Fonts" option if you are expecting
     images from the application are printed in their actual sizes.

(11) The driver's Overlay function is enabled for users who are assigned with
     the Administrators / Power Users right.

(12) When using Scaled booklet with document of mixed orientations, the output
     will be printed in Portrait.

(13) Using large percentage for Scale Factor together with large paper size,
     "Scaling" printing may not be possible.


7. Limitations
==============

(1) The printed output quality of some pattern-on-colour shaded graphic
    images may not be well handled. You may choose a different graphic
    colour/pattern to resemble the desired printout.


(2)  Colour texts are always printed in Black in most applications when Raster
     mode is selected.
     
     Workaround: Select "Vector" mode to print the job.


(3)  Graphic images from Adobe Photoshop 4.0 may not be printed correctly at
     400 DPI.

     Workaround: Select 600 DPI to print the job.


(4)  In Vector printing mode, selecting "All Texts to Black" control may not
     apply to some texts that are greater than 70 points. Texts with large font
     size may be printed as graphics and hence its 'black' attribute is lost.


     Applications that were tested to have this problem are:
       Microsoft PowerPoint 97
       WordPro 97
    
     Workaround: Select "Raster" mode to print the job.


(5)  Some applications draw graphic images on the page before the text is
     drawn in "Raster" mode. As a result, the graphics may be covered by
     the opaque background of the text and hence, these covered images may
     not be printed physically.
 
     Applications that were tested to have this problem are:
       Microsoft WordPad
       Microsoft Excel 97

     Workaround: Select "Vector" mode to print the job.


(6)  Outline texts must be printed using downloaded fonts.
     "Use Printer's TrueType Fonts" option must be unchecked to print texts as
     outline because device (PCL) fonts do not support Outline attribute.


(7)  The texts in the Data Label of Microsoft Excel 97 may have their font
     background each font printed as white in Raster mode.

     Workaround: Select "Vector" mode to print the job.


(8)  The colour lines in the chart of Microsoft Excel 97 may be printed as
     black in Raster mode.

     Workaround: Select "Vector" mode to print the job.


(9) You may get unexpected stapled position if the Staple function is applied
    to the following print jobs:
    > documents that have page orientation different to that of the driver default
      orientation.
    > N-Up printing of documents that have page size different to that of the driver
      default paper size.


(10) The watermark should not be used for creating an overlay. Otherwise, unexpected
     result may occur.


(11) The driver does not support printing from the Client of the Windows NT(R)4.0
     Terminal Server.



8. Known Problems
=================

(1) The N-Up function is not recommended for printing a document that has
    both Portrait and Landscape pages. Depending on the page arrangement of
    a document, the logical page order from one physical page to another
    may be changed.
    For example, if a document has different orientation on its first page
    and third page, the 2-Up printing will output the third and fourth pages
    on the second physical page with swapped order as compared to the first
    and second pages on the first physical page.


(2) If the "Use Document Monitor" option is selected, the Document Monitor will
    start monitoring when the driver starts to process the job. This may cause
    problem in monitoring the job when the job is canceled before it is sent to
    the printer.


Microsoft is the registered trademark of Microsoft Incorporated.
Windows is the registered trademark of Microsoft Incorporated.
Other names of products and companies are the trademarks or
registered trademarks of each company.
--------------------------------< End of File >---------------------------------------




